The Spindleless veneer peeling machine is a veneer lathe under a spindleless condition that includes the veneer knife and at least three rollers. Feeding mechanisms couples to two feeding rollers and a drive system couples to one of the driving rollers. The wood log will driven by three rollers and being peeled to veneer.The veneer thickness can be changed by adjusting the gap between single rolle...

In order to keep the good status of 4ft Spindleless wood veneer making machine, we need to decide the parts need to be lubricated regularly and how to lubricate these parts. 1.Refule the oil tank of screw rod 2.Oil the pressurebar roller reducer 3.Oil the feeding reducer 4.Oil feeding bevel gearbox

Problems and solutions of Spindleless Wood Veneer Machine 1 Problem 1 -Uneven wood veneer Causes: 1.    Poor knife straightness 2.    Decentraction ( not properly aligned) between shaft ends and body 3.    Excessive squeezing force 4.    Serious wood sunny side and shadow side 5.    Too small and not straight wood log Solvi...

Problems and solutions of Spindleless Wood Veneer Machine 3 Problem: The wod veneer is periodically uneven.  Reason: The sunny and shadow surfaces of the wood veneer are too heavy; the peeling knife of veneer lathe/veneer machine  is too low or too high, and the clearance between the single and double roller bearings is too large.  Solutions:  Correctly adjust the height o...

Problems and solutions of Spindleless Wood Veneer Machine 5 Problem: The thickness of the two ends of the remaining wooden shaft is inconsistent, and the wood veneer surface is fan-shaped. Causes:  1.The height of the two ends of the veneer peeling knife is inconsistent; 2. the gap between the two ends of the knife is inconsistent; 3. the single roller bearing is damaged; 4. the screws are lo...

The wood bark is loose and has no use value in the production of plywood. The phloem of the bark tends to block the knife door when peeling, and the rotary knife becomes blunt quickly, and the rotary peeling cannot be carried out normally; the bark often contains metal objects and sand and other debris, such as direct rotary peeling will damage the rotary knife. Affect normal wood veneer peeling a...

The veneer dryer is a continuous veneer drying equipment. The most widely used are mesh belt dryers, roller veneer dryers and platen veneer dryers. 1）The veneer dryer is mainly composed of two parts, a drying section and a cooling section. The drying section is used to heat the veneer and accelerate the discharge of moisture from the veneer through the circulation of hot air. The drying section ca...

1) Most of the veneer dryer machines currently in use use 0.4-1.0MPa saturated steam as the heat source. The radiator is heated first, and then the air is heated to 140-180°C through the radiator, and the hot air transfers the heat to the veneer. The combustion gas of coal gas, petroleum and light diesel fuel is also used to heat the air. 2) The wood veneer dryer machine is equipped with a hot air...

              The meaning of veneer dryer The moisture content of the veneer after rotary cutting is very high. If the veneer is directly sizing without drying treatment, and then the billet is hot-pressed, when the veneer is sizing, due to too much water, it is easy to cause glue bleeding, which will make the veneer glued together. Lack of glue on the surface; b...

The purpose of wood debarking is mainly to facilitate rotary cutting and improve the quality of veneer. The bark is generally composed of outer bark, phloem and cambium. Because the structure of bark is completely different from that of wood (xylem), bark is not only useless in plywood production, but also because its phloem is mostly composed of elongated fibers, if the wood section is directly p...

What is Teeth Roller & Nose Bar Spindleless Veneer Lathe (Gangi) Teeth Roller & Nose Bar Spindleless Veneer Lathe (Gangi) is a new kind of Spindleless veneer peeling machine that has the advantages of Spindle Veneer Peeler and Fiber Tenderizer. Compared to traditional spindleless veneer lathe, where the peeled veneer thickness tolerance is ±0.1-0.15mm, the TNB Spindleless Veneer lathe can ...

What is Teeth Roller & Nose Bar Spindleless Veneer Lathe (Gangi) Teeth Roller & Nose Bar Spindleless Veneer Lathe (Gangi) is a new kind of Spindleless veneer peeling machine that has the advantages of Spindle Veneer Peeler and Fiber Tenderizer. 2020-Sanmu Sansen Design and Manufacture 1st set of TNB ( Teeth roller & Nose bar) Spindleless (Gangi) 2021-2023 Trial prod...

What are the advantages of wood veneer peeled by Teeth roller & Nose bar Spindleless (Gangi)     Combined the advantages of Spindle Veneer Peeling machine and Wood Fiber Tenderizer,Teeth Roller & Nose Bar Spindleless Veneer Lathe (Gangi) can peel good quality veneer.     The advantages is the following:     Firstly, the wood veneer thickness variatio...

How veneer peeled by Nose Bar & Teeth Roller Spindleless Veneer lathe reduce plywood hot pressing cost      During plywood hot pressing, as the temperature and moisture content of the plywood slabs change, the wood veneer is gradually compressed and the thickness of the plywood slabs gradually decreases. This loss is compression loss, which is related to factors such as the hot ...

How veneer peeled by Nose Bar & Teeth Roller Spindleless Veneer lathe reduce plywood sanding cost      Plywood Sanding process is to sand the surface of the plywood to make the surface smooth and beautiful. The waste generated is sanding powder. When the quality of the veneer is good, the amount of sanding is small, and the sanding loss rate is 2% to 5%.     How veneer...